Home > News > Content
High Temperature Heat Resistance Conveyor Belt for Coal Power Plant
Apr 29, 2017

High Temperature Heat Resistance Conveyor Belt for Coal Power Plant

Basic Info

  • Model NO.: High Temperature Heat Conveyor Belt

  • Material: Rubber

  • Feature: Oil-Resistant, Acid And Alkali Resistant, Tear-Resistant, Heat-Resistant, Cold-Resistant, Wear-Resistant

  • Belt Width: 400mm-1600mm

  • Thickness: 4~30mm

  • Trademark: Shunda

  • Specification: SGS, ISO, DIN

  • HS Code: 4010120000

  • Type: NN100-600

  • Inside Material: Nylon

  • Tensile Strength: Strong

  • Piles: 2-10

  • Fabric: Nylon, Ep, Carton, Polyester

  • Transport Package: PP Bag All Side, Steel Pipe Inside

  • Origin: China

Product Description

High Temperature Heat Resistance Conveyor Belts for Coal Power Plant
Our heat resistant conveyor belt adopts SBR or EPDM as covering layer,special high temperature resistant canvas as carcass materials,not only solving the fabric shrinkage and deformation problems under the environment of high temperature,but also avoiding crucial problem as high degree of saturation of ethylene propylene rubber,poor adhesion,it is lighter,of long(about 2-4 times)and good performance of heat resisdence.

Conveyor Belts Product Advantage:
1.Specification is similar to common conveyor belt.
2.GB/T2002-2005 and GB/T7984-2001 Standard are applicable with the international Standard draft ISO/FDISI4890-1999.
3.Heat resistant conveyor belt is divided into three types as follows:

HR120: cover consists mainly of SBR.The belt surface temperature of HR120 belt should be lower then 120ºC,the maximum material temperature for short period can reach 170ºC.The grade of heat resistant conveyor belt is mostly connon used traditional heat resistant conveyor belt,widely used in Cement,coking,metallurgy,chemical,iron and steel industry,etc.
HR50: cover consists mainly of SBR,The belt surface temperature of HR150 should be lower than 150ºC,and the maximum material temperature for short period can reach 200ºC,Comparing to common conveyor belt ,the product is higher temperature resistant,cracking resistant,ageing resistant and of long lifespan,It apply to transport high temperature materials as sintered ore,clinker,coke,dry lime,dry cleay,etc.
HR180:cover consists mainly of EPDM.The belt surface temperature belt of HR150 shoule be not higher than 180ºC,and the maximum material temperature for short period can reach 250ºC,comparing to common conveyor belt,this kind of belt is more cauterant resistant.It forms a dense carbonized layers o belt cover under high temperature to play an effect of heat insulation and cauterant resistance,which can also extend the belt life.It apply to transprot high temperature material as special transport situation as sintering ore and cement field,tec.

The selection of heat resistant conveyor belts
Select different type of heat resistant belt according to the temperature,surface figure,viscosity condition and other concerned data of conveyed materials.For instance, when conveyed material have a temperature of 150ºC,such as the coke or sintered ore etc,and have a relatively small contact area with the belt is surface temperature remains at 60-80ºC,In contrast,when powered material like cement is being conveyed,there is almost no temperature difference between material and belt surface.More information please refer to the following table.

     *The life of heat resistant belt is largely affected by the belt is surface temperature during operation.The belt temperature directly influence not only the adhesion between cover&ply,but also the abrasion and cracking resistant performance of cover rubber.please make full tests of the temperature and other conditions,and then choose the suitable type,
     *Much thicker rubber is very important to ensure much longer life of the belt.
Other products
1.steel cord conveyor belt
2.Multi-ply Fabric Conveyor Belt
3.Corrugated Sidewall Conveyor Belt
4.Tubular Conveyor Belt
5.Sandwich Conveyor Belt

Shipping:

1. By Sea for batch goods

2. Loading port: qingdao , or according to customer's requirement


Payment :

1. Payment:  30% deposit, 70% by T/T against B/L copy. Or by L/C.

2. MOQ: 100M

3. Package Informations:General packing is PP bag all side , rubber core inside

Why choose us :

1.we are manufacturer,so the quality and price are directly controlled by ourself.

2.we owned the latest equipments and our engineers and production managers have more than 10years' experience.OBM ,ODM and OEM are all available.

3.our products have abtained 5 patents,and there're more in applying.

4.our company has built cooperation relationship with many mine and metallury plants ,and their praise proves our quality.

Service:

1.We can provide quality warranty for 3-12 months according to your working condition

2.Our engineer can offer remote or direct guidance if you have got any problem.

3.OEM is also available. what you want is precisely what we hunt.

Welcome to inquiry and contact us by any way.